How To Replace Car Speakers: Upgrading Your Ride

Replacing your car speakers with an enhanced vehicle audio system could always make a difference, especially if you travel to different places. It is an effective improvement you can make for your car and makes you feel like you’re traveling with a live band. But do you already know how to replace car speakers alone?
For some reason, why would you even bring your car to the nearest shop and pay for the replacement, where you can replace it yourself? So, if you want to know about changing car speakers, then you've come to the right place. This article will give you a useful guideline on how to replace car speakers and make your car stereo system's even better. Check out this step-by-step process to follow and absorb how it's done.
Replacing Car Speakers: Step-by-Step Process
Whether your car speakers need replacement because it's starting to wear out, or because you want to improve your car's sound system, there are still plenty of good reasons why it needs to be replaced. That's why many car owners want to know how to replace car speakers because an improved and high-quality sound could always make the trip more relaxed. Below are the useful steps in changing car speakers.
Materials Needed
Here are the materials you're going to prepare in proceeding with the replacement of car speakers.
- Screwdrivers (as many varieties as possible)
- Electrical Tape
- Hobby Knife
- Bits and Torx Drivers
- Drill with screwdriver and bits
- Set of Socket Wrench
- Wiring harness
- Wire Cutter
- Allen Wrenches
- Solder and soldering iron
- Connectors and crimping tools
- Panel removal tool
- Clip Remover
Dash Speakers Replacement
Here are the steps in how to replace car speakers in your dash. The procedure is quite different from replacing the door speakers, and here are the steps to do it.
Step 1: Using a screwdriver, carefully remove the grilles by holding down. It’s ideal to use the 90-degree screwdriver for the removal of the grilles.
Step 2: Once the grille is held in place, slowly pry it up. This is to prevent cracking or scratching your dash if you're doing it. Try using a panel removal tool to pry the grille up.
Step 3: Next is to remove the old speakers. Always make sure to note the polarity of the terminal. You will see that the speaker's positive terminal is larger and comes with a “+” mark or a dot. To attach the new speaker, use your wiring harness or the solder as required by the installation.
Step 4: Once you’re done installing the new speakers, return the grille once again and test it if it’s already working.
Door Speakers Replacement
Since your car’s door speakers are important to make you have a good sound, let’s proceed to the steps on how to replace car speakers in your doors. These speakers are very easy to replace, and here are the steps to follow.
Step 1: Since your car doors need to be opened while installing the speakers, you have to disconnect the battery's negative terminal to prevent you from draining it. This will also help to prevent chances of short circuits in your car's electrical system.
Step 2: Next is to prepare all the materials needed.
Step 3: Slowly remove the factory speakers and the grilles using a flathead screwdriver, and be gentle when you’re replacing it because it’s attached to the wiring harness. If there’s a foam sealant, you might need a hobby knife to cut through the materials. In installing the new speakers, you may use the factory speakers’ screw to ensure the mounting bracket.
Step 4: Next is unplugging and cut the factory wiring harness; gently attach the wiring harness to the new speaker's terminal. Always make sure that the polarity is always correct. Plug the other end of the harness in the factory wiring harness. If it's unavailable, you may use a set of Posi products to make the connections properly.
Step 5: Connect the woofer and tweeter with the attached quick slides. Use the wire ties to gather the cables. Route the speaker wires around the car’s window crank. Once it’s done, you can attach the door panel back onto your car’s door.
Step 6: Make sure to test the speaker before putting it into place. Double-check the connections before re-attaching the factory grille.
Conclusion
Learning how to replace car speakers is just an easy task. However, you need to be careful, especially if you’ll have it in a DIY process, as the level of difficulty involved may vary. But the good thing is that once you know the process and know about how the wiring works, it’s going to be easier for you to do it.
We hope this step-by-step guide on how to replace car speakers has helped you to do it on your own. Just note the wirings and be careful in doing it, as your car's wiring is quite sensitive. You may also watch tutorial videos to make it clearer for you to replace it. Once you know the process, you're not only saving your money; you will also have that best sound experience in your car.